Scanmatik 2 Pro - one of the best j2534 / PassThru diagnostic + chip-tuning device The J2534-RP1210 driver for the SM2 adapter (SM2-PRO) makes it possible to work with a large number of third-party programs that support operation via the J2534 interface. The purpose of the driver development was an attempt to make not the next J2534 adapter “for show”, but the device that most meets the requirements of J2534-1 / 2 and RP1210, as far as the hardware of the SM2 and Scanmatik 2 Pro adapters allows.
The current Windows and Android versions: Scanmatik 2.21.21
List of tested programs:
Allison DOC
CAT Caterpillar Electronic Technician (CAT ET)
Chiploader
Chrysler Flash Application
Combiloader
Cummins Calterm
Cummins Insite
Detroit DDDL
Eaton Service Ranger
ECU Flasher (auto-bk)
Ford Module Programming Tool
Forscan
GM GDS-2/SPS
Hino Diagnostic Explorer
Honda HDS
Jaguar/Land Rover SDD
JCB Service Master 4
MDFLASHER
MMC Flasher (Bruce-Willis)
Nissan Consult 3+
Noregon JPRO
ODIS Service
OpenBox
PCMFlash
Toyota Techstream
Renault CAN Clip
Volvo Premium Tech Tool PTT
Volvo Vida
Wabco Toolbox
Xentry PassThru.
Supported data buses:
ISO-9141 / ISO-14230 (K-LINE)
J1850VPW
J1850PWM
CAN
Single Wire CAN.
Specifications:
Integrated multiplexer for switching diagnostic lines
The broadest support for J2534-1 / 2 standards
Programming voltage supply (5-24V) - to the legs of the OBD2 connector: 6, 8, 11, 12, 13, 14.
Base kit:
Scanmatik 2 Pro
OBD2 cable
USB cable
Car cigarette lighter power cable
Case.
Maximum kit:
Adapter Scanmatik SM2-PRO
OBD2 cable
USB cable 1.8m
Car cigarette lighter power cable
OBD2-GM 12pin
OBD2-GAZ 12pin
GAZ-ABS for ABS Bosch 5.3
OBD2-Mitsubishi 12pin
OBD2-KIA 20pin
OBD2-Fiat 3pin for Fiat, Chery
Deutsch 6 + 9pin
GAZ Westport XCP
ISO-16
OBD2-Mercedes Benz 14pin
SCR-MRS
OBD2-Honda 3pin
Case.
Price depends on the device kit:
Scanmatik 2 Pro (base kit) - $860
Scanmatik 2 Pro (base kit + AUX) - $890
Option:
- Scanmatik 2 Pro bench cable (it's option if you will buy tool) - $140. Boot/bench cable for operation with PCMFlash boot loader modules 53 and 71. There is an indication of the ECU power supply, power, and signal control automatically. An external power supply is required to work with the cable.
- PCMFlash dongle - $39 + any module. This is ECU loader for engine and transmission of Volkswagen, Skoda, Ford, Mazda, Mitsubishi, Nissan / Infiniti, Subaru, Honda / Acura, Hyundai / Kia, Renault, Toyota / Lexus, and others. There are universal modules Denso SH705x Bootloader and BSL TriCore. Supports work with the ADS adapter (version 1, not for all ECU), as well as any J2534 compatible adapter, with the appropriate drivers and libraries. Tested work with OpenPort 2.0, Mongoose JLR, MongoosePro JLR, Teradyne GNA600 (VCM 1), Mazda VCM 2, Scanmatik.
ตรงนี้มีภาพ! แต่ท่านจะมองไม่เห็น , ท่านต้อง
สมัครสมาชิก หรือ
ลงชื่อเข้าระบบ ข้อมูลมาจากที่นี่...
